Previously, if the witness server connection details were provided
to "repmgr witness register" rather than those of the primary server,
repmgr a) write the node record to the witness server rather than
the primary, and b) would loop indefinitely trying to copy the
node table to itself.
Addresses GitHub #538.
Ensure repmgr checks the standby (promotion candidate) is currently
attached to the primary (demotion candidate).
Addresses issue reported in GitHub #519.
Immediately after the demotion candidate (primary) has shut down, we can't
be absolutely sure that the walreceiver has flushed all WAL to disk, so
checking pg_last_wal_receive_lsn() at that point might not reflect
the actual last available WAL location.
To handle this, we'll loop for a while (timeout controlled by configuration
parameter "wal_receive_check_timeout") before finally deciding whether
the standby is still behind the shut-down primary.
Addresses issue raised in GitHub #518.
repmgr will attempt to construct appropriate commands to start
and stop repmgrd, but usually it's preferable for them to be explicitly
defined, particularly if repmgr is installed from packages.
The switchover will fail if the data_directory parameter in repmgr.conf
on the remote node (demotion candidate) is incorrectly configured.
We use the previously added "repmgr node check --data-directory-config
to verify this, and abort early if an issue is discovered.
Implements GitHub #523.
Previously, if connection URIs were in use and "repmgr standby switchover"
was executed, repmgr would pass the connection URI as-is to the demotion
candidate to execute "repmgr node rejoin". However the presence of
unescaped ampersands in the connection URI was causing the rejoin command
to be incorrectly executed.
Addresses GitHub #525.
This suppresses display of the usually lengthy "conninfo" column, mainly
useful for generating a compact table suitable for pasting into emails,
chats etc. without messy line breaks.
Implements GitHub #521.
Previously repmgr would abort with an unhelpful message about being
unable to parse CSV output.
With this commit, it will continue running, and display a list of
inaccessible nodes as an addendum to the main output (unless --csv
or --terse options are specified).
Addresses GitHub #246.
This is to facilitate remote invocation of repmgr when the repmgr
binary is located somewhere other than the PostgreSQL binary directory, as it
cannot be assumed all package maintainers will install repmgr there.
This parameter is optional; if not set (the default), repmgr will fall back
to "pg_bindir" (if set).
Addresses GitHub #246.
Previously, if the server being monitored was not available, repmgrd
would always close the existing connection handle and open a new one.
However, in some cases, e.g. a brief network outage, the existing
connection handle is still good and does not need to be reopened.
This could be particularly problematic if monitoring_history is on,
as this risks leaving orphan sessions on the primary which (given
a sufficiently unstable network) could lead to all available backends
being occupied.
Instead, during an outage we now use a new connection to verify
the server is accessible; if the old connection is still available
(e.g. following a short network interruption) we continue using that;
if not (e.g. the server was restarted), we use the new one.
Previously query texts were always logged at log level DEBUG, but
that doesn't help much in a normal production environment when
trying to identify the cause of issues.
Also make various other minor improvements to query logging and
handling of database errors.
Implements GitHub #498.
Previously repmgr would first check that a replication can be made
from the demotion candidate to the promotion candidate, however it's
preferable to sanity-check the number of available walsenders first,
to provide a more useful error message.
This suppresses log output below log level ERROR. This is useful mainly
when repmgr is being executed programmatically, e.g. in a cronjob,
where it's only useful to receive output if something goes wrong.
Note we advise against using this option when executing repmgr
commands which operate on PostgreSQL nodes (standby follow,
standby promote, standby switchover, node rejoin), particularly when
executed by repmgrd, as the log output will provide valuable
troubleshooting information.
Implements suggestion in GitHub #468.
Default was previously NOTICE (as in repmgr 3.x) but documentation
implied it was INFO, and many of the the documentation examples assume
it is.
This produces some quite informative log output, without creating excessive
log file volume. In particular it's useful to get a better idea of what
repmgrd is actually doing.
Also add documentation section for the log configuration parameters.
GitHub #470, containing change suggested in GitHub #467.
