Immediately after the demotion candidate (primary) has shut down, we can't
be absolutely sure that the walreceiver has flushed all WAL to disk, so
checking pg_last_wal_receive_lsn() at that point might not reflect
the actual last available WAL location.
To handle this, we'll loop for a while (timeout controlled by configuration
parameter "wal_receive_check_timeout") before finally deciding whether
the standby is still behind the shut-down primary.
Addresses issue raised in GitHub #518.
In some places we were still providing "false" from the original implementation,
which was intended to indicate whether a negative value was allowed.
This has not been a problem, as it merely means we have been providing "0",
which is the same thing; however we can finer-tune some of the calls
(e.g. node ID must be or greater).
In some circumstances, e.g. while performing a switchover, it is essential
that repmgrd does not take any kind of failover action, as this will put
the cluster into an incorrect state.
Previously it was necessary to stop repmgrd on all nodes (or at least
those nodes which repmgrd would consider as promotion candidates), however
this is a cumbersome and potentially risk-prone operation, particularly if the
replication cluster contains more than a couple of servers.
To prevent this issue from occurring, this patch introduces the ability
to "pause" repmgrd on all nodes wth a single command ("repmgr daemon pause")
which notifies repmgrd not to take any failover action until the node
is "unpaused" ("repmgr daemon unpause").
"repmgr daemon status" provides an overview of each node and whether repmgrd
is running, and if so whether it is paused.
"repmgr standby switchover" has been modified to automatically pause repmgrd
while carrying out the switchover.
See documentation for further details.
Previously, "repmgr standby switchover" used the configuration file parameters
"reconnect_interval" and "reconnect_attempts" to define a timeout to determine
whether the current primary (demotion candidate) has shut down.
However, these parameters are intended for primary failure detection and are
generally lower in value, while a controlled shutdown may take longer, resulting
in the switchover being aborted as repmgr was not waiting long enough.
To prevent this happening, parameter "shutdown_check_timeout" has been added.
This complements the existing "standby_reconnect_timeout" parameter used
by "repmgr standby switchover".
Implements GitHub #504.
Currently the (very generic sounding) "standby_reconnect_timeout" configuration
file parameter is used in several different contexts and it would be useful
to have more granular control over the different timeouts it's used to configure.
This patch introduces "node_rejoin_timeout", used in place of "standby_reconnect_timeout"
(which wasn't documented) when "repmgr node rejoin" is executed, to determine
how long to wait for the node to rejoin the replication cluster.
Additionally "repmgrd_standby_startup_timeout" is introduced as a timeout for
failover situations, when repmgrd executes "repmgr standby follow" to follow
a new primary, and waits for the standby to restart and become available
for connections.
"standby_reconnect_timeout" is now only relevant for "repmgr standby switchover".
Implements GitHub #454.
After restarting the standby, poll pg_stat_replication on the upstream
until the standby connects, and exit with an error if it doesn't by the
timeout defined in "standby_follow_timeout".
Implments GitHub #444.
This is used for determining a timeout when reconnecting to the standby
after executing the "follow_command". This will normally not need to be
set explicitly, but maybe useful in cases where the standby's startup
phase can last longer than usual.
This previously happened in the extension SQL code, which could
potentially cause replay problems if installing on a BDR cluster.
As this table is only required for streaming replication failover,
move the initialisation to "repmgr primary register".
Addresses GitHub #344 .
the wait()-macros (WEXITSTATUS etc.) live in sys/wait.h as per
1003.1, and on some platforms (notably FreeBSD) compilation will
fail if wait.h isn't included explicitely.
If the current primary (demotion candidate) still has any files to archive,
it will delay the shutdown until all files are archived. If there is a
substantial number of files, and/or the archive command executes slowly,
this will probably lead to an unwelcome delay in the switchover process.
In previous versions of repmgr, some options had ambiguous meanings,
and/or were used for slightly different purposes. This way we end
up with a couple more options (most of which probably won't need
adjusting) but greater clarity and flexibility.
Removed:
master_reponse_timeout:
renamed to "async_query_timeout", as this was its main usage
retry_promote_interval_secs:
replaced by "primary_notification_timeout"
Added:
async_query_timeout:
timeout (in seconds) when executing asynchronous queries
primary_notification_timeout:
number of seconds to wait for notification from the new primary
after a failover
primary_follow_timeout:
number of seconds to wait for the new primary to become available
when executing "repmgr standby follow"
