This functionality enables repmgrd (when running on the primary) to
monitor connected child nodes. It will log connections and disconnections
and generate events.
Additionally, repmgrd can execute a custom script if the number of connected
child nodes falls below a configurable threshold. This script can be used
e.g. to "fence" the primary following a failover situation where a new primary
has been promoted and all standbys are now child nodes of that primary.
In Barman mode, if there is an existing, populated data directory, and
the "--force" option is provided, the entire directory was being deleted,
and later recreated as part of the rsync process, but with the default
permissions.
Fix this by recreating the data directory with the correct permissions
after deleting it.
This enable selection of the method repmgrd uses to check whether the upstream
node is available. Possible values are:
- "ping" (default): uses PQping() to check server availability
- "connection": executes a query on the connection to check server
availability (similar to repmgr3.x).
With long-running copy operations, it's possible the connection(s) to
the primary/source server may go away for some reason, so recheck
their availability before attempting to reuse.
We only want to check the status of physical replication slots
to determine whether a streaming replication standby has become
detached and there is therefore a risk of uncontrolled WAL buildup
on the local node.
It's not feasible to second-guess the state of logical replication
slots.
If, for whatever reason, repmgrd is not running on a node, but that
node qualifies as promotion candidate, failover will not take place
as that node will never promote itself.
We therefore discount nodes where repmgrd is running as promotion
candidates, which will ensure one node is always promoted.
There is a slight risk here that the node(s) where repmgrd is not running
are further ahead, leading to a timeline fork. It might be possible
to mitigate that by having the "election" leader perform the promote
(or follow) operation.
Previously, if the witness server connection details were provided
to "repmgr witness register" rather than those of the primary server,
repmgr a) write the node record to the witness server rather than
the primary, and b) would loop indefinitely trying to copy the
node table to itself.
Addresses GitHub #538.
Ensure repmgr checks the standby (promotion candidate) is currently
attached to the primary (demotion candidate).
Addresses issue reported in GitHub #519.
Immediately after the demotion candidate (primary) has shut down, we can't
be absolutely sure that the walreceiver has flushed all WAL to disk, so
checking pg_last_wal_receive_lsn() at that point might not reflect
the actual last available WAL location.
To handle this, we'll loop for a while (timeout controlled by configuration
parameter "wal_receive_check_timeout") before finally deciding whether
the standby is still behind the shut-down primary.
Addresses issue raised in GitHub #518.
repmgr will attempt to construct appropriate commands to start
and stop repmgrd, but usually it's preferable for them to be explicitly
defined, particularly if repmgr is installed from packages.
The switchover will fail if the data_directory parameter in repmgr.conf
on the remote node (demotion candidate) is incorrectly configured.
We use the previously added "repmgr node check --data-directory-config
to verify this, and abort early if an issue is discovered.
Implements GitHub #523.
Previously, if connection URIs were in use and "repmgr standby switchover"
was executed, repmgr would pass the connection URI as-is to the demotion
candidate to execute "repmgr node rejoin". However the presence of
unescaped ampersands in the connection URI was causing the rejoin command
to be incorrectly executed.
Addresses GitHub #525.
This suppresses display of the usually lengthy "conninfo" column, mainly
useful for generating a compact table suitable for pasting into emails,
chats etc. without messy line breaks.
Implements GitHub #521.
Previously repmgr would abort with an unhelpful message about being
unable to parse CSV output.
With this commit, it will continue running, and display a list of
inaccessible nodes as an addendum to the main output (unless --csv
or --terse options are specified).
Addresses GitHub #246.
This is to facilitate remote invocation of repmgr when the repmgr
binary is located somewhere other than the PostgreSQL binary directory, as it
cannot be assumed all package maintainers will install repmgr there.
This parameter is optional; if not set (the default), repmgr will fall back
to "pg_bindir" (if set).
Addresses GitHub #246.
