repmgr/doc/repmgr-daemon-start.xml

<refentry id="repmgr-daemon-start">
  <indexterm>
    <primary>repmgr daemon start</primary>
  </indexterm>

  <indexterm>
    <primary>repmgrd</primary>
    <secondary>starting</secondary>
  </indexterm>

  <refmeta>
    <refentrytitle>repmgr daemon start</refentrytitle>
  </refmeta>

  <refnamediv>
    <refname>repmgr daemon start</refname>
    <refpurpose>Start the &repmgrd; service</refpurpose>
  </refnamediv>

  <refsect1>
    <title>Description</title>
    <para>
      This command starts the &repmgrd; service on the
      local node.
    </para>
    <para>
      By default, &repmgr; will wait for up to 15 seconds to confirm that &repmgrd;
      started. This behaviour can be overridden by specifying a diffent value using the <option>--wait</option>
      option, or disabled altogether with the <option>--no-wait</option> option.
    </para>

    <important>
      <para>
        The <filename>repmgr.conf</filename> parameter <varname>repmgrd_service_start_command</varname>
        must be set for <command>repmgr daemon start</command> to work; see section
        <xref linkend="repmgr-daemon-start-configuration"/> for details.
      </para>
    </important>
  </refsect1>



  <refsect1>

    <title>Options</title>

    <variablelist>

      <varlistentry>
        <term><option>--dry-run</option></term>
        <listitem>
          <para>
            Check prerequisites but don't actually attempt to start &repmgrd;.
          </para>
          <para>
            This action will output the command which would be executed.
          </para>
        </listitem>
      </varlistentry>

      <varlistentry>
        <term><option>-w</option></term>
        <term><option>--wait</option></term>
        <listitem>
          <para>
            Wait for the specified number of seconds to confirm that &repmgrd;
            started successfully.
          </para>
          <para>
            Note that providing <option>--wait=0</option> is the equivalent of <option>--no-wait</option>.
          </para>

         </listitem>
      </varlistentry>

      <varlistentry>
        <term><option>--no-wait</option></term>
        <listitem>
          <para>
            Don't wait to confirm that &repmgrd;
            started successfully.
          </para>
          <para>
            This is equivalent to providing <option>--wait=0</option>.
          </para>
         </listitem>
      </varlistentry>

    </variablelist>
  </refsect1>

  <refsect1 id="repmgr-daemon-start-configuration" xreflabel="repmgr daemon start configuration">
    <title>Configuration file settings</title>
    <para>
     The following parameter in <filename>repmgr.conf</filename> is relevant
     to <command>repmgr daemon start</command>:
    </para>

    <variablelist>

      <varlistentry>

        <term><option>repmgrd_service_start_command</option></term>
        <listitem>
          <indexterm>
            <primary>repmgrd_service_start_command</primary>
            <secondary>with &quot;repmgr daemon start&quot;</secondary>
          </indexterm>

          <para>
            <command>repmgr daemon start</command> will execute the command defined by the
            <varname>repmgrd_service_start_command</varname> parameter in <filename>repmgr.conf</filename>.
            This must be set to a shell command which will start &repmgrd;;
            if &repmgr; was installed from a package, this will be the service command defined by the
            package. For more details see <link linkend="appendix-packages">Appendix: &repmgr; package details</link>.
          </para>
          <important>
            <para>
              If &repmgr; was installed from a system package, and you do not configure
              <varname>repmgrd_service_start_command</varname> to an appropriate service command, this may
              result in the system becoming confused about the state of the &repmgrd;
              service; this is particularly the case with <literal>systemd</literal>.
            </para>
          </important>
        </listitem>
      </varlistentry>
    </variablelist>

  </refsect1>


  <refsect1>
    <title>Exit codes</title>
    <para>
      One of the following exit codes will be emitted by <command>repmgr daemon start</command>:
    </para>
    <variablelist>

      <varlistentry>
        <term><option>SUCCESS (0)</option></term>
        <listitem>
          <para>
            The &repmgrd; start command (defined in
            <varname>repmgrd_service_start_command</varname>) was successfully executed.
          </para>
          <para>
            If the <option>--wait</option> option was provided, &repmgr; will confirm that
            &repmgrd; has actually started up.
          </para>
        </listitem>
      </varlistentry>

      <varlistentry>
        <term><option>ERR_BAD_CONFIG (1)</option></term>
        <listitem>
          <para>
            <varname>repmgrd_service_start_command</varname> is not defined in
            <filename>repmgr.conf</filename>.
          </para>
        </listitem>
      </varlistentry>


      <varlistentry>
        <term><option>ERR_DB_CONN (6)</option></term>
        <listitem>
          <para>
            &repmgr; was unable to connect to the local PostgreSQL node.
          </para>
          <para>
            PostgreSQL must be running before &repmgrd;
            can be started. Additionally, unless the <option>--no-wait</option> option was
            provided, &repmgr; needs to be able to connect to the local PostgreSQL node
            to determine the state of &repmgrd;.
          </para>
        </listitem>
      </varlistentry>


      <varlistentry>
        <term><option>ERR_REPMGRD_SERVICE (27)</option></term>
        <listitem>
          <para>
            The &repmgrd; start command (defined in
            <varname>repmgrd_service_start_command</varname>) was not successfully executed.
          </para>
          <para>
            This can also mean that &repmgr; was unable to confirm whether &repmgrd;
            successfully started (unless the <option>--no-wait</option> option was provided).
          </para>
        </listitem>
      </varlistentry>

    </variablelist>
  </refsect1>

  <refsect1>
    <title>See also</title>
    <para>
      <xref linkend="repmgr-daemon-stop"/>, <xref linkend="repmgrd-daemon"/>, <xref linkend="repmgr-service-status"/>
    </para>
  </refsect1>

</refentry>